SERVO T 6000 Semi-mounted reversible ploughs
6 to 9 furrows, power class up to 500 hp
Inquiry
Description
The SERVO T 6000 is the result of many years of ploughing experience and intensive development work at PÖTTINGER. The main beam section and the NOVA stone protection system have been revised from the ground up to optimise reliability. The straightforward and quick adjustment of the relevant settings and a tight turning radius at the headland save valuable time.
Advantages
PLUS models
A high degree of flexibility is a basic requirement for efficient work in the field. While working around trees, pits, masts and other obstacles takes up a lot of time with a rigid plough, only one adjustment needs to be made with the PLUS hydraulic working width adjustment system. This means the plough can be adapted quickly and safely to changing conditions in the field. At the same time, the quality of work remains consistent. The furrow width of the first body is always automatically transferred to the remaining furrows.
Thanks to the PLUS system, it is possible to quickly adjust the furrow width to plough around obstacles, field edges and headlands. The different formation of the furrow ridges when changing the working width has agronomic advantages. All specifications are met with a full adjustment range between 35 and 58 cm on each plough body. Our standard ploughs have 5-step manual furrow width adjustment.
Drive outside the furrow
For more soil conservation and when using tractors with wide tyres, dual wheels or crawler tracks, the SERVO T 6000 and the ON LAND versions can also be driven outside the furrow. This reduces soil pressure in deeper soil layers and prevents compaction of the furrow bottom. In addition, the pull line is in a straight line when ploughing outside the furrow. This results in less side pull, more efficient power transmission and less wear. Precision work is possible thanks to the use of steering systems. However, if this is not possible due to the site conditions, the plough beam can also be set for in the furrow if required.
Additional flexibility
With a few steps you can switch from ploughing in the furrow to on land ploughing. To achieve this, the ON LAND beam link shifts the plough beam outwards. This means that it can be used with tractors with an outer width of up to 4 m metres. In order to ensure consistent depth control, an additional front depth control wheel is implemented as a pivot depth wheel within the frame. Due to intelligent use of the spool valves, no additional connection is necessary.
All the advantages at a glance
1. Mounting
Cat. III and Cat. IV double sided linkage lugs for the lower linkage guarantees high strength. These ensure that power is transmitted efficiently from the tractor to the plough.
-
Turning angle of over 90 degrees possible
2. TRACTION CONTROL
The weight transferred to the rear axle of the tractor by the hydraulic cylinder increases traction and reduces slippage. Increased traction is essential for cost effective operation because it saves time and money.
-
Up to 1.1 kg more ballast
3. Turnover mechanism
Two telescopic hydraulic cylinders turnover the plough reliably and smoothly at the headland. These are mechanically locked during road transport. Easily adjustable, rugged stops ensure precise beam angle adjustment.
4. PLUS
The furrow width can easily be adjusted from the tractor seat. The furrow width does not affect the width of the front plough body.
-
Working widths of 35 cm to 58 cm on each plough body
Technical parameters
SERVO T 6000 N (Standard Version)
| Parameter | (6 furrows) | (7 furrows) | (8 furrows) | (9 furrows) |
|---|---|---|---|---|
| Beam | 160 × 160 mm | 160 × 160 mm | 160 × 160 mm | 160 × 160 mm |
| Furrow spacing & working width | 102 (35–41–47–52–58) cm | 102 (35–41–47–52–58) cm | 102 (35–41–47–52–58) cm | 102 (35–41–47–52–58) cm |
| Underframe clearance | 80 / 90 cm | 80 / 90 cm | 80 / 90 cm | 80 / 90 cm |
| Weight | 3010 kg | 3280 kg | 3600 kg | 3890 kg |
| Body spacing | 102 cm | 102 cm | 102 cm | 102 cm |
| Leg size | 80 × 35 mm | 80 × 35 mm | 80 × 35 mm | 80 × 35 mm |
SERVO T 6000 N
| Parameter | (6 furrows) | (7 furrows) | (8 furrows) |
|---|---|---|---|
| Beam | 160 × 160 mm | 160 × 160 mm | 160 × 160 mm |
| Furrow spacing & working width | 102 (35–41–47–52–58) cm | 102 (35–41–47–52–58) cm | 102 (35–41–47–52–58) cm |
| Underframe clearance | 80 cm | 80 cm | 80 cm |
| Weight | 3690 kg | 4080 kg | 4510 kg |
| Body spacing | 102 cm | 102 cm | 102 cm |
| Leg size | 80 × 35 mm | 80 × 35 mm | 80 × 35 mm |
SERVO T 6000 P
| Parameter | (6 furrows) | (7 furrows) | (8 furrows) | (9 furrows) |
|---|---|---|---|---|
| Beam | 160 × 160 mm | 160 × 160 mm | 160 × 160 mm | 160 × 160 mm |
| Furrow spacing & working width | 102 (35–58) cm | 102 (35–58) cm | 102 (35–58) cm | 102 (35–58) cm |
| Underframe clearance | 80 / 90 cm | 80 / 90 cm | 80 / 90 cm | 80 / 90 cm |
| Weight | 3230 kg | 3540 kg | 3880 kg | 4180 kg |
| Body spacing | 102 cm | 102 cm | 102 cm | 102 cm |
| Leg size | 80 × 35 mm | 80 × 35 mm | 80 × 35 mm | 80 × 35 mm |
Photos
Video
